For this to work, You will need:

• Satin ribbon, wide. 5 cm. – White, purple, pink;
• Satin ribbon, wide. 2.5 cm. – White, purple, pink;
• Ribbon Organza wide. 4 cm. – Green;
• White Satin fabric (not very big piece).
• Felt;
• Hot-melt adhesive;
• Magnets – 4 pieces;
• Thin plastic for the base;
• Beads;
• Thin wire;
• Cable – 3 m .

Before you make directly, grabs the curtains, I have prepared with flowers from acute petals – kanzashi, something like a lily. For each pick up: on the third large, double flowers and 14 be small, single.

First, I have prepared with sharp petals. On each flower, it took 10 Th petals as the flowers themselves, I decided to do the double. Lower petals on all flowers are white, while the upper petals – pink and purple flowers. How to fold the petals show on pink.

1. Of wide ribbon. 5 cm. Square cut out.
2. Fold the square diagonally, wrong sides together.
3. The resulting triangle folded again.
4. Then fold the third time and cut edge (see photo he noted, blue, dotted line). Cropped for what would align the cut, all the layers. Clamped with forceps.

5. Cropped side, raised it to a candle to tape slightly melted. Tip: to fuse the best in the area of ​​the wick (here less bloat). Flame if concerned, it is only slightly. Petal held several times along the fire that melted to the whole region.
6. When the cut edge, slightly melted, holding it with tweezers for a few seconds, what would tape glued together.
7. The result petal, as in the photo №7.
8. Then turned the petal, as in the photo №8.


These petals, I have prepared: white – 30 pcs, pink – 20 pieces, purple – 10 pieces.


Now, you can collect the flowers.
9. glued white and pink petals. To do this, on the white petal, along the folds, caused hotmelt. And once on top, put a rose petal (so I packed 20 pcs. Of white and pink and 10 pcs. White and purple petals).
10. When the double petals were collected, began to gather flowers. Hotmelt is applied to the edge of white petals and clung to him, the edge, the next tab. Clay, I tried to put slightly before reaching the mid to late petal. By the way, can be varied as will be open flower. If the band is a little touch of petals – the flower is open longer and vice versa.
11. to collect 5-Th double, petals. Spread past, not glued petals, caused glue and pressed.
12. According to this principle, I gathered all the double petals. As a result I got: 6 pcs. large, double flowers, 3 pcs, for each pickup.



such hue was not. So I just cut the ribbon br. 5 cm. From a square of 5 cm. Impossible – 4th square of 2.5 cm. Inside I soldering, using a ruler.White-pink flowers, I did, just because of the pink ribbon, there are very few. Total work – 28 pcs, 14-Tb, each tiebacks.



Now, I had to make the stamens. Here I decided to experiment. Long wanted to make the stamens of wire, for two reasons:

1. That you could bend the stamens, in its sole discretion.
2. And most importantly, I wanted to make the work volume. When the flowers are glued directly to any basis, it turns out all in one plane and not enough natural volume.

But looking ahead, I will say that this experiment, I was not quite satisfied. It was necessary to use a wire, a little more resilient, or do the stamens of a different material. Stamens of this wire had spread after they accidentally primnesh. One thing I was reassured that this is not a decoration for hair that is constantly removed / worn. Holders curtains hung, as it should, stamens straightened and let hang. But this experience was for me useful))).
And so I took the wire, put small beads in the middle of the wire and twisted it .


For small flowers, I used one stamens. But for large, twisted together, five stamens.


Is glued to the large flower stamens, I:

1. In the bead (larger than the beads on the stamens), is passed 5 stamens be twisted together and inserted it all in flower. Here, in the center of the flower, it was not sealed space (by the way, that’s why, gluing together the petals, I tried to apply the adhesive, a little before reaching the base of the petal). And then, the bead rises, that she would not interfere, when I apply the adhesive.
2. Then, at the bottom of the flower does slightly hot melt adhesive, and lowers the bead pressing it.
3. After the glue has cooled, made foot flower. Took a skewer and wrapped around, around the wire, as in the photo №3.
4. In small flowers, beads stamens, pasted, immediately to the bottom of the flower. And also, leg curl (photo №4).